Introduction Of Automobile — Part 2 MCQs with Explanations

Sain and Pandit is the correct answer to “Which company made hard moped”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Gives colour and filling up effect to the paint is the correct answer to “The purpose of adding pigment to the paint is that it”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

On the axle and inside axle casing is the correct answer to “In Semi floating type rear axle, the bearing is located”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

One is the correct answer to “A 'bucket seat' can accomodate how, many persons”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Suction, Compression, Power, Exhaust is the correct answer to “The correct order in which the four operations occur in four stroke engine is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

All of these is the correct answer to “Which of the following is the Indian manufacturer of moped”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Scooter is the correct answer to “Vijay Super 150 CC is a . . . . . . . .”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Mass of flywheel is the correct answer to “The fluctuation of engine speed during a cycle depends upon”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Standard is the correct answer to “Which one of the following is not a trade name of tractor in India”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Impeller is the correct answer to “The pump part that rotates and causes water circulation between the radiator and the engine is called the”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Both A and B is the correct answer to “Stroke means piston movement from”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Bending, torsional stresses and end thrust is the correct answer to “The axle shaft of a semi floating rear axle is subjected to”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Exhaust and intake strokes is the correct answer to “Valve overlap occurs between”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Toyota is the correct answer to “Foreigner vehicle is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

5.5 m is the correct answer to “The front axle of a car has pivot centers 1.3 m apart. The angle of inside lock is 40! and the angle of the outside lock is 35!. What is the wheelbase of the car”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

1000 is the correct answer to “How many times in a minute does each valve on a four stroke engine running at 2000 RPM open and close”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

90° is the correct answer to “The angle between the cylinder axes and the crankshaft centre line in an engine is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

The road adhesion is increased is the correct answer to “In case of a four wheel driven vehicle”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Silieo-chrome steel is the correct answer to “The material used for inlet valve is usually”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

C. I. engines and S. I. engines is the correct answer to “Two types of engines used in automobiles are”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Both closed is the correct answer to “During the power stroke in a four stroke engine, the inlet valve and exhaust valves are”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Audi 100 SE is the correct answer to “Five cylirtder in line engine is used in”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

All of these is the correct answer to “Which of the following is an example of transmission system”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Wheel impact with road obstacls is the correct answer to “The frame may get distorted to a parallelogram shape due to”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Drag link is the correct answer to “Another name for the steeing link rod is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Interference fit is the correct answer to “The detachable dry liner in the form of plain sleeve is pressed into the cast iron or aluminium alloy cylinder block with . . . . . . . .”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Two is the correct answer to “The minimum number of compression rings in an automotive engine is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Overhead valve mechanism is the correct answer to “Most commonly used valve actuating mechainsm in modem cars is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Front axle is the correct answer to “What is fitted at the front of the vehicles by means of spring assemblies”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

The time for which the points remain closed is the correct answer to “The 'dwell' is:”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

True is the correct answer to “In unit type body (frameless body) design, the sheet metal parts are welded together, forming a frame work to which outer skin is attached.”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Punch is the correct answer to “Before drtlling a hole, its centre should be marked with a”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

All of the above is the correct answer to “Cylinder blocks of IC engines are commonly made of . . . . . . . .”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

The part of the vehicle, designed to absorb the energy during a collision is the correct answer to “The crumple zone is”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Positive camber is the correct answer to “The angle formed by the wheel with the vertical when the top of the wheel slants outward is called”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Vikram is the correct answer to “Producer of three wheeler vehicle is . . . . . . . .”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Valve springs is the correct answer to “The engine valves are closed by”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Absence of valves is the correct answer to “A two stroke IC engine is identified by”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Rear engine front drive is the correct answer to “Which of the following layputs is not used in motor vechicles”. This question is standard in competitive examination syllabi for Introduction Of Automobile.

Ensures effective transmission of engine torque to all four wheels, even on slippery road surfaces is the correct answer to “The basic purpose of a four wheel drive (4WD) system is that it”. This question is standard in competitive examination syllabi for Introduction Of Automobile.