Wheels And Tires — Part 2 MCQs with Explanations

Inset wheel is the correct answer to “A wheel so constructed that the centre line of the rim is located in board of the attachment face of the disc is called-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Excessive accelecration and braking is the correct answer to “Heel' and 'toe wear' in tyres is caused by”. This question is standard in competitive examination syllabi for Wheels And Tires.

In single spots is the correct answer to “Out of round brake drums cause the tyres to wear”. This question is standard in competitive examination syllabi for Wheels And Tires.

Wheel balance is the correct answer to “Weight can be attached to wheel rim to correct”. This question is standard in competitive examination syllabi for Wheels And Tires.

Aspect ratio is the correct answer to “A tyre is designated as : 175/70 R 13. The number 70 represents”. This question is standard in competitive examination syllabi for Wheels And Tires.

The front tyres worn faster than the rear tyres is the correct answer to “On a front wheel drive vehicle, how do the tyres usually worn out”. This question is standard in competitive examination syllabi for Wheels And Tires.

Increase traction is the correct answer to “The purpose of tyre sipes is to”. This question is standard in competitive examination syllabi for Wheels And Tires.

Steel is the correct answer to “Bead wires are made of”. This question is standard in competitive examination syllabi for Wheels And Tires.

Width of tyre is the correct answer to “In the tyre 8.25 × 20 - 10 PR, 8.25 indicator-”. This question is standard in competitive examination syllabi for Wheels And Tires.

High pressure tyre is the correct answer to “In trucks are use-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Tread is the correct answer to “The thick layer of rubber on the outside circum-ference of the tyre is called-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Heating rubber urider pressure is the correct answer to “Vulcanizing means”. This question is standard in competitive examination syllabi for Wheels And Tires.

8000 kms is the correct answer to “To equalize tyre wear, it is suggested that tyres be rotated from one wheel to another every”. This question is standard in competitive examination syllabi for Wheels And Tires.

Cord plies is the correct answer to “. . . . . . . . gives strength to resist internal pressure to support load and road shocks”. This question is standard in competitive examination syllabi for Wheels And Tires.

Using wider rims and low aspect ratio tyres is the correct answer to “The better road adhesion is obtained in light alloy wheels because of”. This question is standard in competitive examination syllabi for Wheels And Tires.

Tension is the correct answer to “In case of a wire wheel the vehicle weight is supported by the wires in”. This question is standard in competitive examination syllabi for Wheels And Tires.

Minimum is the correct answer to “The tyre should create . . . . . . . . noise while running on the road.”. This question is standard in competitive examination syllabi for Wheels And Tires.

Incorrect camber angle and toe in is the correct answer to “For wheel and tyre troubles the cause of one side wear of tyres is -”. This question is standard in competitive examination syllabi for Wheels And Tires.

Off the car only is the correct answer to “Wheels must be balanced”. This question is standard in competitive examination syllabi for Wheels And Tires.

All are correct is the correct answer to “Which of the following is a type of wheel”. This question is standard in competitive examination syllabi for Wheels And Tires.

Near centre is the correct answer to “An over-inflated tyre will wear the tread most”. This question is standard in competitive examination syllabi for Wheels And Tires.

Near the edges is the correct answer to “An under-inflated tyre will wear the tread most”. This question is standard in competitive examination syllabi for Wheels And Tires.

Both are correct is the correct answer to “For wheel and tyre troubles the cause of the troulble uniform rapid wear is-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Tyre and the road surface is the correct answer to “The rolling resistance is because of the friction between the”. This question is standard in competitive examination syllabi for Wheels And Tires.

Radial ply tyres is the correct answer to “Tread distortion is least on”. This question is standard in competitive examination syllabi for Wheels And Tires.

Rubber is the correct answer to “The side walls are . . . . . . . . compound which serve as protective covering to the casing.”. This question is standard in competitive examination syllabi for Wheels And Tires.

Equalise wear is the correct answer to “The purpose of tyre rotation on automobiles is to”. This question is standard in competitive examination syllabi for Wheels And Tires.

Demountable rim is the correct answer to “The rim which can be removed easily from the wheel is called-”. This question is standard in competitive examination syllabi for Wheels And Tires.

8.20" is the correct answer to “If the size of the tyre is 8.20 × 20 × 10 PR. The shows that the width of tyre from shoulder to shoulder is-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Rubber is the correct answer to “The tyre casing are made up of layers of cord impregnated with-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Smoother ride at low speeds is the correct answer to “In comparison with a radial tyre, one advantage of a bias ply tyre is”. This question is standard in competitive examination syllabi for Wheels And Tires.

All of these is the correct answer to “The main advantage of steel disc wheel is”. This question is standard in competitive examination syllabi for Wheels And Tires.

All are correct is the correct answer to “Which of the following is/are the types of tyre, used in automobiles”. This question is standard in competitive examination syllabi for Wheels And Tires.

Bead is the correct answer to “The portion of tyre which holds the tyre on the rim is-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Section width is the correct answer to “Ina tyre, it is designated as 'P200/75 R16'. What is the digit 200”. This question is standard in competitive examination syllabi for Wheels And Tires.

Front two wheels will have a Common centre during turning is the correct answer to “When an automobile takes a tum to avoid the skidding and over turning”. This question is standard in competitive examination syllabi for Wheels And Tires.

Turning radius of the left and right wheels is the correct answer to “The purpose of turning radius gauges is to measure the”. This question is standard in competitive examination syllabi for Wheels And Tires.

On the tyre, where the tread meets the side wall is the correct answer to “Tread wear indicator is located:”. This question is standard in competitive examination syllabi for Wheels And Tires.

Both are correct is the correct answer to “To perform a good function the wheel must be-”. This question is standard in competitive examination syllabi for Wheels And Tires.

Uncomfortable ride at low speeds is the correct answer to “The disadvantage of radial ply tyre as compared to cross ply tyre is”. This question is standard in competitive examination syllabi for Wheels And Tires.